Unication E5 Spécifications Page 131
- Page / 186
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
6 - 15
6 Programless Communications
E5C-T Digital Controllers Programmable Type Communications Manual (H186)
6-2 E5@C-T Controller Setup
6
6-2-9 Copying Parameter Settings
You can copy the settings of all parameters except for the Communications Unit No. parameter from the
master (i.e., the Controller with communications unit number 0) to one or more of the slaves (i.e., the
Controllers with communications unit numbers other than 0). Copying parameters is possible only
between Controllers with the same model number. You also cannot copy parameter settings to a Con-
troller with a version that is older than the version of the master. All of the slaves are automatically reset
after the copying operation is completed. Make sure that the system will not be adversely affected
before you copy parameter settings.
Communications Setting Level
Display condition: The Protocol Setting parameter must be set to cmp, fins, or mcp4 and the Commu-
nications Unit No. parameter must be set to 0 (master).
Copying Procedure Starting from the Initial Status
(1) Connect the master and slaves with RS-485 connections and turn ON the power
supply.
(2) Set the Communications Unit No. parameters of the slaves in order starting from 1
and then return to the operation level.
(3) Set all of the parameters in the master except for those in the communications
setting level.
(4) Change the master to the communications setting level and change the
communications settings as given below.
Change the Protocol Setting parameter, set the Communications Unit No. parameter to 0,
set the Communications Baud Rate parameter to 57.6, set the Send Data Wait Time
parameter to 1, and set the Highest Communications Unit No. parameter to the highest
communications unit number that is set.
Change the other parameters in the communications setting level as required.
Do not return to the operation level while you are changing the parameter settings. If you
mistakenly return to the communications setting level, return the Communications Baud
Rate parameter to 9.6, return to the operation level, and then set the Communications Baud
Rate parameter again.
6-2-9 Copying Parameter Settings
Case in which copying
is possible
The model numbers and versions are the same.
Example: Copying data from the E5CC-TRX3ASM-002 (V1.0) to the
E5CC-TRX3ASM-002 (V1.0)
Cases in which copying
is not possible
The model numbers are different.
Example: Copying data from the E5CC-TRX3ASM-002 to the E5CC-TQX3ASM-002
The versions are different.
Example: Copying data from the E5CC-TRX3ASM-002 (V1.0) to the
E5CC-TRX3ASM-002 (V1.1)
Parameter name
Displayed
characters
Setting range Default
Copy copy off (Copying failed: e0**)
all
1 to 31
off
- Programmable Type 1
- Preface 3
- © OMRON, 2014 3
- Warranties 4
- Limitation on Liability; Etc 4
- Safety Precautions 6
- CAUTION 7
- Precautions for Safe Use 9
- Precautions for Safe Use 10
- Trademarks 11
- Versions 12
- Revision History 13
- Revision History 14
- Sections in This Manual 15
- CONTENTS 16
- Section A Appendices 18
- Communications Methods 19
- 1-1-1 Introduction 20
- 1-1-3 Transmission Procedure 21
- 1-1-4 Interface 21
- 1-1-5 Wiring 21
- 1 Communications Methods 22
- CompoWay/F Communications 25
- Procedures 25
- 2-1 Data Format 26
- 2-1-2 BCC Calculation Example 27
- 2-1-3 Response Frame 27
- 2-1-4 Communications Data 28
- 2-1-5 End Code Example 28
- 2-1 Data Format 29
- 2-1-5 End Code Example 29
- 2-2 Structure of Command Text 30
- 2-2-4 Addresses 31
- 2-2-5 Number of Elements 31
- Variable 32
- 2-3-2 Write Variable Area 33
- Response 36
- -5CCT AEX3R 38
- 2-3-7 Echoback Test 39
- (2) Response Code 40
- • Normal Completion 40
- • Error Occurred 40
- 2-3-8 Operation Command 41
- 2-3-8 Operation Command 43
- 2-4 Response Code List 46
- Communications Data for 47
- CompoWay/F 47
- 3-2 Status and Status 2 77
- 3-2 Status and Status 2 79
- Modbus Communications 81
- Procedure 81
- 4-1 Data Format 82
- 4-1 Data Format 83
- 4-1-1 Command Frame 83
- 4-1-2 Response Frame 84
- 4-1-3 Error Codes 85
- 4-2 Function List 86
- 4-3 Variable Area 87
- 4-4-1 Variable Read, Multiple 88
- Response Frame 89
- Response Code 89
- H'10 90
- Command Frame 92
- 4-4-4 Echoback Test 94
- PID set is fixed at PID1 98
- 5-2 Status 115
- Programless Communications 117
- 6-1-1 Introduction 119
- 6-1-2 Features 119
- 6-1-5 Connectable PLCs 121
- 6-2 E5@C-T Controller Setup 122
- 6-2-3 Send Data Wait Time 123
- Communications Setting Level 125
- 6-2-6 Receive Data Wait Time 126
- 6-2 E5@C-T Controller Setup 129
- Troubleshooting 133
- 6-2-10 Communications Writing 134
- 6-3 Controlling Programless 136
- Communications 136
- 6-3-2 Response Flag 137
- 6-3-4 Operation Command Codes 138
- 6-3-6 Write Mode 138
- 6-3-7 Troubleshooting 139
- CX-Programmer and USB driver 140
- 6-4-3 PLC Setup 141
- 6-4-3 PLC Setup 143
- 6-4-4 E5@C-T Controller Setup 144
- SCU21-V1 145
- 6-4-5 Checking Operation 146
- 6-4-5 Checking Operation 147
- Changing E5CC-T Settings 148
- Connecting to the PLC 152
- 6-5-3 PLC Setup 152
- 6-5-3 PLC Setup 153
- 6-5-4 E5@C-T Controller Setup 155
- 6-5-5 Checking Operation 155
- USB port 156
- USB connector 156
- Commercially 156
- QJ71C24N-R4 157
- (4) Click the OK Button 158
- (5) Click the Execute Button 158
- 6-6-3 PLC Setup 159
- 6-6-4 E5@C-T Controller Setup 162
- 6-6-5 Checking Operation 163
- 6-6-5 Checking Operation 165
- Component Communications 169
- 7-1 Component Communications 170
- 7-1-2 Wiring 171
- Initial Setting Level 172
- Operation Level 172
- Adjustment Level 172
- 7 Component Communications 173
- 7-2 Operation for Component 174
- 7-3 Troubleshooting 175
- Appendices 177
- A-1 ASCII List 178
- A-2 Troubleshooting 179
- A Appendices 180
- Contact: www.ia.omron.com 186
© 2020, manymanuals.fr. Tous droits réservés | 0.681 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels