Unication E5 Spécifications Page 141
- Page / 186
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
6 - 25
6 Programless Communications
E5C-T Digital Controllers Programmable Type Communications Manual (H186)
6-4 Connecting to CP-series PLCs
6
6-4-2 Switch Settings and Wiring
Before you attach the CP1W-CIF11 to the CP1E, turn OFF pin 4 on the DIP switch for operation set-
tings on the back of the CP1W-CIF11 and turn ON the rest of the pins.
Wire the CP1W-CIF11 to the E5CC-T Controllers as shown below.
Note: 1 The maximum transmission distance is 50 m for the CP1W-CIF11 and 500 m for the CP1W-CIF21.
2 For wiring methods, refer to A-3-2 Recommended RS-422A/485 Wiring in the CP1E CPU Unit Hardware
User’s Manual (Cat. No. W479).
Set up communications on the CP1E to enable communicating with the E5CC-T Controllers.
PLC operation will stop and the power supply will be cycled during the setup procedure. Make sure that
this will not create any problems in the controlled system.
z Connecting to the PLC
(1) Connect the computer to the CP1E with a USB cable and then start the
CX-Programmer.
(2) Select PLC
−
Auto Online
−
Direct Online from the menu bar.
6-4-2 Switch Settings and Wiring
Pin OFF ON Setting
1 No terminating resistance
Terminating resistance on both
ends
Terminating resistance selection
2 4-wire
2-wire 2-wire or 4-wire selection
3 4-wire
2-wire Same as above.
4
--- --- Not used.
5 RS control disabled. (Signal
always received.)
RS control enabled. RS control selection for RD
6 RS control disabled. (Signal
always sent.)
RS control enabled. RS control selection for SD
6-4-3 PLC Setup
Shield Shield Shield
13
14
E5CC-T
No.0
E5CC-T
No.1
E5CC-T
No.2
B(+)
A(−)
13
14
B(+)
A(−)
13
14
B(+)
A(−)
CP1W-CIF11
120
Ω (1/2 W)
terminating resistance
- Programmable Type 1
- Preface 3
- © OMRON, 2014 3
- Warranties 4
- Limitation on Liability; Etc 4
- Safety Precautions 6
- CAUTION 7
- Precautions for Safe Use 9
- Precautions for Safe Use 10
- Trademarks 11
- Versions 12
- Revision History 13
- Revision History 14
- Sections in This Manual 15
- CONTENTS 16
- Section A Appendices 18
- Communications Methods 19
- 1-1-1 Introduction 20
- 1-1-3 Transmission Procedure 21
- 1-1-4 Interface 21
- 1-1-5 Wiring 21
- 1 Communications Methods 22
- CompoWay/F Communications 25
- Procedures 25
- 2-1 Data Format 26
- 2-1-2 BCC Calculation Example 27
- 2-1-3 Response Frame 27
- 2-1-4 Communications Data 28
- 2-1-5 End Code Example 28
- 2-1 Data Format 29
- 2-1-5 End Code Example 29
- 2-2 Structure of Command Text 30
- 2-2-4 Addresses 31
- 2-2-5 Number of Elements 31
- Variable 32
- 2-3-2 Write Variable Area 33
- Response 36
- -5CCT AEX3R 38
- 2-3-7 Echoback Test 39
- (2) Response Code 40
- • Normal Completion 40
- • Error Occurred 40
- 2-3-8 Operation Command 41
- 2-3-8 Operation Command 43
- 2-4 Response Code List 46
- Communications Data for 47
- CompoWay/F 47
- 3-2 Status and Status 2 77
- 3-2 Status and Status 2 79
- Modbus Communications 81
- Procedure 81
- 4-1 Data Format 82
- 4-1 Data Format 83
- 4-1-1 Command Frame 83
- 4-1-2 Response Frame 84
- 4-1-3 Error Codes 85
- 4-2 Function List 86
- 4-3 Variable Area 87
- 4-4-1 Variable Read, Multiple 88
- Response Frame 89
- Response Code 89
- H'10 90
- Command Frame 92
- 4-4-4 Echoback Test 94
- PID set is fixed at PID1 98
- 5-2 Status 115
- Programless Communications 117
- 6-1-1 Introduction 119
- 6-1-2 Features 119
- 6-1-5 Connectable PLCs 121
- 6-2 E5@C-T Controller Setup 122
- 6-2-3 Send Data Wait Time 123
- Communications Setting Level 125
- 6-2-6 Receive Data Wait Time 126
- 6-2 E5@C-T Controller Setup 129
- Troubleshooting 133
- 6-2-10 Communications Writing 134
- 6-3 Controlling Programless 136
- Communications 136
- 6-3-2 Response Flag 137
- 6-3-4 Operation Command Codes 138
- 6-3-6 Write Mode 138
- 6-3-7 Troubleshooting 139
- CX-Programmer and USB driver 140
- 6-4-3 PLC Setup 141
- 6-4-3 PLC Setup 143
- 6-4-4 E5@C-T Controller Setup 144
- SCU21-V1 145
- 6-4-5 Checking Operation 146
- 6-4-5 Checking Operation 147
- Changing E5CC-T Settings 148
- Connecting to the PLC 152
- 6-5-3 PLC Setup 152
- 6-5-3 PLC Setup 153
- 6-5-4 E5@C-T Controller Setup 155
- 6-5-5 Checking Operation 155
- USB port 156
- USB connector 156
- Commercially 156
- QJ71C24N-R4 157
- (4) Click the OK Button 158
- (5) Click the Execute Button 158
- 6-6-3 PLC Setup 159
- 6-6-4 E5@C-T Controller Setup 162
- 6-6-5 Checking Operation 163
- 6-6-5 Checking Operation 165
- Component Communications 169
- 7-1 Component Communications 170
- 7-1-2 Wiring 171
- Initial Setting Level 172
- Operation Level 172
- Adjustment Level 172
- 7 Component Communications 173
- 7-2 Operation for Component 174
- 7-3 Troubleshooting 175
- Appendices 177
- A-1 ASCII List 178
- A-2 Troubleshooting 179
- A Appendices 180
- Contact: www.ia.omron.com 186
© 2020, manymanuals.fr. Tous droits réservés | 1.261 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels