Unication E5 Spécifications télécharger pdf (Page 104)

5 Communications Data for Modbus

5 - 10

E5C-T Digital Controllers Programmable Type Communications Manual (H186)

*1 Valid only with external communications.

Address

Parameter name Setting (monitor) value Level

Four-byte

mode

Two-byte

mode

0E14 2E0A Event Input Assignment 1 H'00000000 (0): None

H'00000001 (1): RUN (OFF)/RESET (ON)

H'00000002 (2): RUN (ON)/RESET (OFF)

H'00000003 (3): Auto/Manual Switch

H'00000004 (4): RESET

H'00000005 (5): RUN

H'00000006 (6): Hold/clear hold

H'00000007 (7): Hold

H'00000008 (8): Advance

H'00000009 (9): Program No. switch 0

H'0000000A (10): Program No. switch 1

H'0000000B (11): Program No. switch 2

H'0000000C (12): Direct/reverse operation

H'0000000D (13): Program SP mode/fixed SP mode

H'0000001E (14): 100% AT execute/cancel

H'0000001F (15): 40% AT execute/cancel

H'00000010 (16): All PID 100% AT execute/cancel

H'00000011 (17): All PID 40% AT execute/cancel

H'00000012 (18): Setting Change Enable/Disable

H'00000013 (19): Communications Writing Enable/Disable

*1

H'00000014 (20): Alarm Latch Cancel

H'00000015 (21): Wait enable (ON)/Disable (OFF)

Initial setting

0E16 2E0B Event Input Assignment 2 H'00000000 to H'00000015 (0 to 21)

Note: Same as for Event Input Assignment 1.

0E18 2E0C Event Input Assignment 3 H'00000000 to H'00000015 (0 to 21)

Note: Same as for Event Input Assignment 1.

0E1A 2E0D Event Input Assignment 4 H'00000000 to H'00000015 (0 to 21)

Note: Same as for Event Input Assignment 1.

0E1C 2E0E Event Input Assignment 5 H'00000000 to H'00000015 (0 to 21)

Note: Same as for Event Input Assignment 1.

0E1E 2E0F Event Input Assignment 6 H'00000000 to H'00000015 (0 to 21)

Note: Same as for Event Input Assignment 1.

0E20 2E10 Auxiliary Output 1

Assignment

H'00000000 (0): Not assigned.

H'00000001 (1): Control output (heating)

H'00000002 (2): Control output (cooling)

H'00000003 (3): Alarm 1

H'00000004 (4): Alarm 2

H'00000005 (5): Alarm 3

H'00000006 (6): Alarm 4

H'00000007 (7): Heater alarm

H'00000008 (8): HB alarm

H'00000009 (9): HS alarm

H'0000000A (10): Input error

H'0000000B (11): Program end output

H'0000000C (12): Stage output

H'0000000D (13): RUN output

H'0000000E (14): Time signal 1 output

H'0000000F (15): Time signal 2 output

H'00000010 (16): Integrated alarm

H'00000011 (17): Work bit 1

H'00000012 (18): Work bit 2

H'00000013 (19): Work bit 3

H'00000014 (20): Work bit 4

H'00000015 (21): Work bit 5

H'00000016 (22): Work bit 6

H'00000017 (23): Work bit 7

H'00000018 (24): Work bit 8

Advanced

function

setting

0E22 2E11 Auxiliary Output 2

Assignment

H'00000000 to H'00000018 (0 to 24)

Note: Same as for the Auxiliary Output 1 Assignment parameter.

0E24 2E12 Auxiliary Output 3

Assignment

H'00000000 to H'00000018 (0 to 24)

Note: Same as for the Auxiliary Output 1 Assignment parameter.

0E26 2E13 Auxiliary Output 4

Assignment

H'00000000 to H'00000018 (0 to 24)

Note: Same as for the Auxiliary Output 1 Assignment parameter.

1 2 ... 99 100 101 102 103 104 105 106 107 108 109 ... 185 186

Commentaires sur ces manuels

Pas de commentaire